'/%3e%3cpath%20d='M8%200.5C12.1421%200.5%2015.5%203.85786%2015.5%208C15.5%2012.1421%2012.1421%2015.5%208%2015.5C3.85786%2015.5%200.5%2012.1421%200.5%208C0.5%203.85786%203.85786%200.5%208%200.5Z'%20fill='url(%23paint1_linear_0_45845)'%20stroke='white'/%3e%3cpath%20d='M10.0597%204.5332C10.031%204.5332%2010.0036%204.54817%209.98859%204.57313L8.09724%207.79442C8.02613%207.90046%207.84897%208.23731%207.5483%208.7875C7.37863%209.0969%207.25387%209.32771%207.17152%209.48615C7.1341%209.55727%207.0293%209.53855%207.01807%209.45871C6.97191%209.11936%206.89456%208.6066%206.78727%207.91793L6.2483%204.61804C6.24207%204.57812%206.20713%204.54942%206.16721%204.54942H4.28085C4.2297%204.54942%204.18977%204.59683%204.201%204.64798L5.71059%2012.1959C5.71808%2012.2346%205.75176%2012.2621%205.79044%2012.2621H7.46845C7.49715%2012.2621%207.52335%2012.2471%207.53832%2012.2234L12.1869%204.65796C12.2205%204.60307%2012.1806%204.5332%2012.117%204.5332H10.0597Z'%20fill='white'/%3e%3cdefs%3e%3clinearGradient%20id='paint0_linear_0_45845'%20x1='8.99711'%20y1='15.3526'%20x2='47.3575'%20y2='15.3526'%20gradientUnits='userSpaceOnUse'%3e%3cstop%20stop-color='%23AF86FF'/%3e%3cstop%20offset='1'%20stop-color='%23774EFF'/%3e%3c/linearGradient%3e%3clinearGradient%20id='paint1_linear_0_45845'%20x1='1.1152'%20y1='15.1368'%20x2='15.3888'%20y2='15.1368'%20gradientUnits='userSpaceOnUse'%3e%3cstop%20stop-color='%23AF86FF'/%3e%3cstop%20offset='1'%20stop-color='%23774EFF'/%3e%3c/linearGradient%3e%3c/defs%3e%3c/svg%3e)
- J5点亮x8b时，只有亮度很高的灯管才会感应图像，并且偏色（紫色），其他部分很模糊
anshi底层软件2023-09-182023-09-18
- get yuv failed，同时G0 MIPI_SIF_MODULE module dq too much timeout error_detail -3anshi底层软件2023-09-072023-09-07
- J5 RX1 max96712 上 Enable 1 Links in GMSL2 mode后 , 摄像头和加串器的i2c 地址消失anshi底层软件2023-08-162023-08-16
- 点亮两颗模组时，只有一颗摄像头能出图anshi底层软件2023-08-032023-08-03
- 已解决x3上不能点亮两颗sensoranshi底层软件X3 SDB2023-07-192023-07-19
- 已解决ovx3c不能出图anshi底层软件2023-07-032023-07-03
- 已解决ovx3c点亮时host1 MIPIHOSTIOC_START erroranshi底层软件2023-06-302023-06-30
- 已解决i2cdetect不到摄像头的地址anshi底层软件2023-06-272023-06-27
- 已解决96712+9295点亮四个 ovx3c 时，pipe(0)TIME OUT，get raw failedanshi底层软件X3 SDB2023-06-202023-06-20
- 已解决使用96712+9295点亮4颗sensor，只有一颗sensor出图anshi底层软件征程52023-06-142023-06-14
- 已解决96712+9295点亮四个 ovx3c 时，正常出图一段时间后 G0 IPU_MODULE select too much timeout, retryanshi底层软件X3 SDB2023-06-132023-06-13
- 已解决使用96712+9295点亮成功之后，停止再运行出现错误anshi底层软件征程52023-06-092023-06-09
- 已解决新增加的AWB功能时不能被调用anshi底层软件征程52023-05-262023-05-26
- 已解决AWE功能通过网络连接测试anshi底层软件征程52023-05-252023-05-25
- 已解决POC功能怎么测试anshi底层软件征程52023-05-232023-05-23
- 已解决96712的J5 不能同步触发anshi底层软件征程52023-05-182023-05-18
- 已解决求助96712的J5 同步触发模式怎么验证和确认anshi底层软件征程52023-05-162023-05-16
- 已解决96712 接四个 ovx3c 时不能四路出图anshi底层软件征程52023-05-082023-05-08
- 已解决96712 接四个 ovx3c 时pipeline was nullanshi底层软件征程52023-05-042023-05-04
- 已解决96712 接四个 ovx3c 时 Remote I/O erroranshi底层软件征程52023-04-262023-04-26